Description

The FT-MTRS-2E30-01 is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The MTRS-2E30-01 series converts a 10Gb/s serial electrical data stream to 10Gb/s optical output signalanda10Gb/sopticalinputsignalto10Gb/s serial electrical data streams.The high speed 10Gb/selectricalinterfaceisfullycompliantwith XFIspecification(builtinCDRonbothTXand RX) andallowsFR4 host PCB trace upto 200mm.The MTRS-2E30-01isdesignedforuseinavarietyof

10Gb/s  equipment  SDH/SONET  (9.95Gb/s), EthernetLAN(10.3Gb/s)andFC(10.5Gb/s).The customercanadjustinterface’electricallevelto select 8.5G~11.3G rate section. The high performance 1310nm DFB transmitter coupled with a high sensitivity PIN receiver provide superiorperformanceforapplicationsupto10km with SMF. The fully compliant SFP form factor provideshighdensityapplications,hotplugabilityeasyoptical port upgradesand lowEMI emission.

TheSFP+LRw/CDRmodule electricalinterfaceis compliant to XFI electrical specifications.      The transmitterinputandreceiveroutputimpedanceis

100Ohmsdifferential.  Datalinesareinternally AC coupled. The module provides differential termination and reduce differential to common modeconversionforqualitysignalterminationand lowEMI.  XFItypicallyoperatesover200mmof improvedFR4materialoruptoabout150mmof standard FR4with one connector.

Features

●  10Gb/s serial optical interface

●  1310nm DFB  transmitter, PIN photo-detector

●  Transmission  distance  up  to  10Km with SMF

●  LC duplex conector
●  Integrated clock and data recovery (CDR) function
●  Operating casetemperature:0°C~70°C

Applications

●  SONET(OC-192)/SDH(STM64)

●  10GBASE-LR (10.3125Gbps)

●  10GBASE-LW (9.953Gbps)

Compliance

●  CompliantwithIEEE 802.3ae-200210G Base-LR

●  CompliantwithSFF-8431 & SFF-8083 & SFF-8432 & SFF-8472
●  Compliant with RoHS

Specification

Notes:

[1]Data rate tolerance  10GBASE-LR/LW: typ.+/-100ppm

[2]Measuredat9.953Gbps,Non-framed PRBS2^31-1,NRZ

[3]Measured byusing SFP+evaluationboard.

Notes:

[1]Time from rising edge ofTXDisable towhen theopticaloutput fallsbelow10% of nominal

[2]Time from falling edge ofTXDisable towhenthemodulatedoptical outputrisesabove90% ofnominal

[3] From poweron or negationofTXFault usingTXDisable

[4]Time fromfault toTXfault on

[5]TimeTXDisable mustbe held high to resetTX_fault

[6]Time fromLOSstatetoRXLOSassert

[7]Time fromnon-LOS state toRXLOSdeassert.

[8]TimefromrisingorfallingedgeofRateSelectinputuntilreceiverbandwidthisinconformancewithappropriate specification

DigitalDiagnosticFunction

ThefollowingdigitaldiagnosticcharacteristicsaredefinedovertheRecommendedOperatingEnvironmentunless otherwisespecified.ItiscomplianttoSFF-8472Rev11.1withinternalcalibrationmode.Forexternalcalibrationmode

please contactour salesstuff.

Table6:Digitaldiagnosticspecificationtable

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.