标准光模块
CFP-SR10光模块
Specifications
- 产品型号: CFP-100G-SR10
- 兼容品牌: 全系列
- 封装类型: Up to 11.2 Gbps per channel bandwidth
- 传输速率: 103.125 & 111.810 Gbit/s Dual Rate Operation
- 传输距离: OM3 p to 300m and OM4 up to 400m
- 发射波长: 850nm
- 接收波长: 10 channels 850nm VCSEL array
- 工作温度: 商业级0℃～+70℃/工业级-40℃～+85℃ 可选
- 数字诊断: 带DDM
- 接收灵敏度: 10 channels PIN photo detector array
- 接收灵敏度: 10 channels PIN photo detector array
Description
F-tone Networks 100G CFP Optical Transceiver Module
CFP-100G-SR10/CSR10XX
Features
- Transmission data rate up to 11.2Gbit/s per channel
- CFP MSA compliant
- Compliant to IEEE 802.3ba specification for 100GBASE-SR10 links
- Up to 11.2 Gbps per channel bandwidth,
- OTU4 compatible
- 10 channels 850nm VCSEL array
- 10 channels PIN photo detector array
- OM3 Multimode Fiber cable of up to 300m and OM4 Multimode Fiber cable of up to 400m
- MDIO digital diagnostic and control capabilities.
- compliant to CFP MSA Management Interface Specification, Draft 1.4
- TX input and RX output CDR retiming
- Hot pluggable electrical interface
- Power class 1 (<8W max)
- Operating case temperature
Standard : 0 to +70°C
Industrial : -40 to +85°C
- 3.3V power supply
- RoHS 6 compliant(lead free)
Applications
- High-speed core router interlinks and data center aggregation
- Test equipment
Description
The CFP optical transceiver module are a high performance, low power consumption, short reach(1m to 100m) interconnect solution supporting 100G Ethernet and PCIe. It is compliant with the CFP MSA and IEEE P802.3ba 100GBASE-SR10. F-tone Networks CFP SR10 modules offer 10 transmit and 10 receive asynchronous channels operating at up to 11.2Gbps per channel.
As shown in Figure 1, the transmitter side of the module consists of an array of VCSELs (Vertical Cavity Surface Emitting Lasers) and associated circuitry, which converts 10 parallel electrical data inputs to 10 parallel optical data output signals and also converts 10 parallel optical signals into 10 parallel electrical signals through an array of PIN photodiodes and associated circuitry.
Absolute Maximum Ratings
|
Parameter |
Symbol |
Min |
Max |
Unit |
|
Supply Voltage |
Vcc |
-0.3 |
3.6 |
V |
|
Input Voltage |
Vin |
-0.3 |
Vcc+0.3 |
V |
|
Storage Temperature |
Tst |
-20 |
85 |
ºC |
|
Case Operating Temperature |
Top |
0 |
70 |
ºC |
|
Humidity(non-condensing) |
Rh |
5 |
95 |
% |
Recommended Operating Conditions
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Supply Voltage |
Vcc |
3.13 |
3.3 |
3.47 |
V |
|
Operating Case temperature |
Tca |
0 |
70 |
ºC |
|
|
Data Rate Per Lane |
fd |
- |
11.2 |
Gbps |
|
|
Humidity |
Rh |
5 |
85 |
% |
|
|
Power Dissipation |
Pm |
8 |
W |
Electrical Characteristics
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Differential input impedance |
Zin |
90 |
100 |
110 |
ohm |
|
Differential Output impedance |
Zout |
90 |
100 |
110 |
ohm |
|
Differential input voltage amplitude |
ΔVin |
120 |
820 |
mVp-p |
|
|
Differential output voltage amplitude |
ΔVout |
300 |
820 |
mVp-p |
|
|
Input Logic Level High |
VIH |
2.0 |
VCC |
V |
|
|
Input Logic Level Low |
VIL |
0 |
0.8 |
V |
|
|
Output Logic Level High |
VOH |
VCC-0.5 |
VCC |
V |
|
|
Output Logic Level Low |
VOL |
0 |
0.4 |
V |
Optical Characteristics
Transmitter Optical Specifications (T = 25°C, VCC =3.3V +/- 5%)
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Average Optical Power(per channel) |
Pout |
-8 |
-2.5 |
+1 |
dBm |
|
Average Optical Power(per channel) - Disabled |
Poff |
-30 |
dBm |
||
|
Optical Return Loss Tolerance |
12 |
dB |
|||
|
Extinction Ratio |
ER |
3 |
dB |
||
|
Center Wavelength |
λc |
840 |
850 |
860 |
nm |
|
RMS Spectral Width |
λ |
0.5 |
0.65 |
nm |
|
|
Transmitter eye mask |
Compliant to IEEE802.3ba eye mask specification |
||||
Note：
1. Average optical power is measured at the output of the modules optical interface.
Receiver Optical Specifications (T = 25°C, VCC =3.3V +/- 5%)
|
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Optical Power Sensitivity(per channel) |
Pin min |
-12 |
-9.9 |
dBm |
|
|
Optical Power Saturation(per channel) |
Pin max |
+1 |
dBm |
||
|
Stressed Receiver Sensitivity |
PS |
-5.4 |
dBm |
||
|
Center Wavelength |
λc |
840 |
850 |
860 |
nm |
|
RMS Spectral Width |
λ |
0.5 |
0.65 |
nm |
|
|
Optical Return Loss |
Rl |
12 |
dB |
||
Note：
Optical power sensitivity is measured with BER@10>-12 at 10.3125Gbps per channel.
Part A:Bottom Row Pin Function Definition
|
Pin |
Symbol |
Type |
I/O |
Description |
|
1 |
3.3V_GND |
GND |
3.3V Module Supply Voltage Return Ground, can be separate or tied together with Signal Ground |
|
|
2 |
3.3V_GND |
GND |
||
|
3 |
3.3V_GND |
GND |
||
|
4 |
3.3V_GND |
GND |
||
|
5 |
3.3V_GND |
GND |
||
|
6 |
3.3V |
VCC |
3.3V Module Supply |
|
|
7 |
3.3V |
VCC |
||
|
8 |
3.3V |
VCC |
||
|
9 |
3.3V |
VCC |
||
|
10 |
3.3V |
VCC |
||
|
11 |
3.3V |
VCC |
||
|
12 |
3.3V |
VCC |
||
|
13 |
3.3V |
VCC |
||
|
14 |
3.3V |
VCC |
||
|
15 |
3.3V |
VCC |
||
|
16 |
3.3V_GND |
GND |
||
|
17 |
3.3V_GND |
GND |
||
|
18 |
3.3V_GND |
GND |
||
|
19 |
3.3V_GND |
GND |
||
|
20 |
3.3V_GND |
GND |
||
|
21 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
22 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
23 |
GND |
GND |
||
|
24 |
(TX_MCLKn) |
CML |
O |
CML For optical waveform testing. Not used. |
|
25 |
(TX_MCLKp) |
CML |
O |
CML For optical waveform testing. Not used. |
|
26 |
GND |
GND |
||
|
27 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
28 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
29 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
30 |
PRG_CNTL1 |
LVCMOS w/PU |
I |
Programmable Control 1 set via MDIO, MSA default: TRXIC_RSTn – TX & RX IC reset. “0” = reset, “1” or NC = enabled or not used |
|
31 |
PRG_CNTL2 |
LVCMOS w/PU |
I |
Programmable Control 2 set via MDIO, MSA default: Hardware power Interlock LSB, “00” = <8W, “01” = <16W, “10” < 24W, “11” or NC = >24W or not used |
|
32 |
PRG_CNTL3 |
LVCMOS w/PU |
I |
Programmable Control 3 set via MDIO, MSA default: Hardware power Interlock MSB, “00” = <8W, “01” = <16W, “10” < 24W, “11” or NC = >24W or not used |
|
33 |
PRG_ALRM1 |
LVCMOS |
O |
Programmable Alarm 1 set via MDIO, Reflex default: HIPWR_ON, Module power on indicator. “1” = Module high power up completed, “0” = Module not high powered up |
|
34 |
PRG_ALRM2 |
LVCMOS |
O |
Programmable Alarm 2 set via MDIO, Reflex default: MOD_READY, module initialization complete, “1” = complete, “0” = not complete |
|
35 |
PRG_ALRM3 |
LVCMOS |
O |
Programmable Alarm 3 set via MDIO, Reflex default: MOD_FAULT, module fault detected, “1” = fault, “0” = no fault |
|
36 |
TX_DIS |
LVCMOS w/PU |
I |
Transmitter Disable for all channels, “1” or NC = transmitter disabled, “0” = transmitter enabled |
|
37 |
MOD_LOPWR |
LVCMOS w/PU |
I |
Module low power mode. “1” or NC = module in low power (safe) mode, “0” = power-on enabled |
|
38 |
MOD_ABS |
GND |
O |
Module Absent. “1” or NC = Module absent, “0” = module present. Pull-up resistor on Host |
|
39 |
MOD_RSTn |
LVCMOS w/PD |
I |
Module Reset. “0” = reset the module, “1” or NC = module enabled, Pull Down resistor in module |
|
40 |
RX_LOS |
LVCMOS |
O |
Receiver loss of optical signal on any channel, “1” = loss of signal, “0” = normal condition |
|
41 |
GLB_ALRMn |
LVCMOS |
O |
Global Alarm. “0” = alarm condition in any MDIO alarm register, “1” = no alarm |
|
42 |
PRTADR4 |
1.2V CMOS |
I |
MDIO port address bit 4 |
|
43 |
PRTADR3 |
1.2V CMOS |
I |
MDIO port address bit 3 |
|
44 |
PRTADR2 |
1.2V CMOS |
I |
MDIO port address bit 2 |
|
45 |
PRTADR1 |
1.2V CMOS |
I |
MDIO port address bit 1 |
|
46 |
PRTADR0 |
1.2V CMOS |
I |
MDIO port address bit 0 |
|
47 |
MDIO |
1.2V CMOS |
I/O |
Management Data I/O bi-directional data (electrical specs as per 802.3ae) |
|
48 |
MDC |
1.2V CMOS |
I |
Management data clock (electrical specs as per 802.3ae) |
|
49 |
GND |
GND |
||
|
50 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
51 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
52 |
GND |
GND |
||
|
53 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
54 |
NC |
I/O |
F-tone Networks internal, do not connect |
|
|
55 |
3.3V_GND |
GND |
3.3V Module Supply Voltage Return Ground, can be separate or tied together with Signal Ground |
|
|
56 |
3.3V_GND |
GND |
||
|
57 |
3.3V_GND |
GND |
||
|
58 |
3.3V_GND |
GND |
||
|
59 |
3.3V_GND |
GND |
||
|
60 |
3.3V |
VCC |
3.3V Module Supply |
|
|
61 |
3.3V |
VCC |
||
|
62 |
3.3V |
VCC |
||
|
63 |
3.3V |
VCC |
||
|
64 |
3.3V |
VCC |
||
|
65 |
3.3V |
VCC |
||
|
66 |
3.3V |
VCC |
||
|
67 |
3.3V |
VCC |
||
|
68 |
3.3V |
VCC |
||
|
69 |
3.3V |
VCC |
||
|
70 |
3.3V_GND |
GND |
||
|
71 |
3.3V_GND |
GND |
||
|
72 |
3.3V_GND |
GND |
||
|
73 |
3.3V_GND |
GND |
||
|
74 |
3.3V_GND |
GND |
Part b:Top Row Pin Function Definition
|
Pin |
Symbol |
Pin |
Symbol |
|
|
148 |
GND |
111 |
GND |
|
|
147 |
Not used |
110 |
Not used |
|
|
146 |
Not used |
109 |
Not used |
|
|
145 |
GND |
108 |
GND |
|
|
144 |
Not used |
107 |
RX9n |
|
|
143 |
Not used |
106 |
RX9p |
|
|
142 |
GND |
105 |
GND |
|
|
141 |
TX9n |
104 |
RX8n |
|
|
140 |
TX9p |
103 |
RX8p |
|
|
139 |
GND |
102 |
GND |
|
|
138 |
TX8n |
101 |
RX7n |
|
|
137 |
TX8p |
100 |
RX7p |
|
|
136 |
GND |
99 |
GND |
|
|
135 |
TX7n |
98 |
RX6n |
|
|
134 |
TX7p |
97 |
RX6p |
|
|
133 |
GND |
96 |
GND |
|
|
132 |
TX6n |
95 |
RX5n |
|
|
131 |
TX6p |
94 |
RX5p |
|
|
130 |
GND |
93 |
GND |
|
|
129 |
TX5n |
92 |
RX4n |
|
|
128 |
TX5p |
91 |
RX4p |
|
|
127 |
GND |
90 |
GND |
|
|
126 |
TX4n |
89 |
RX3n |
|
|
125 |
TX4p |
88 |
RX3p |
|
|
124 |
GND |
87 |
GND |
|
|
123 |
TX3n |
86 |
RX2n |
|
|
122 |
TX3p |
85 |
RX2p |
|
|
121 |
GND |
84 |
GND |
|
|
120 |
TX2n |
83 |
RX1n |
|
|
119 |
TX2p |
82 |
RX1p |
|
|
118 |
GND |
81 |
GND |
|
|
117 |
TX1n |
80 |
RX0n |
|
|
116 |
TX1p |
79 |
RX0p |
|
|
115 |
GND |
78 |
GND |
|
|
114 |
TX0n |
77 |
Not used |
|
|
113 |
TX0p |
76 |
Not used |
|
|
112 |
GND |
75 |
GND |
Ordering information
|
Part Number |
Product Description |
|
CFP-100G-SR10 |
CFP 100G SR10, 100m on OM3 MMFand 150m on OM4 MMF;0 to +70°C |
|
CFP-100G-CSR10 |
CFP 100G SR10, 300m on OM3 MMFand 400m on OM4 MMF;0 to +70°C |
|
CFP-100G-SR10I |
CFP 100G SR10, 100m on OM3 MMFand 150m on OM4 MMF;-40 to +85°C |
|
CFP-100G-CSR10I |
CFP 100G SR10, 300m on OM3 MMFand 400m on OM4 MMF;-40 to +85°C |
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must bespecifically confirmed in writing by F-tone Networks before they become applicable to any particular order orcontract. In accordance with the F-tone Networks policy of continuous improvement specifications may changewithout notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.
Related Products
CFP4 Optical Transceiver
This CFP Multi-Source Agreement (MSA) defines the CFP4 form factor of an optical transceiver which can support 40Gbit/s and 100Gbit/s interfaces for Ethernet, ITU-T OTN and other applications. Specifications provided in this document are given as a “delta” to the CFP MSA Hardware Specification Rev.1.4 or the CFP2 Hardware Specification Rev. 1.0.
CFP 100GBASE-SR10 OTU4 Parallel Optical Module
CFP 100GBASE-SR10 / OTU4 Parallel Optical Module:Designed to support the IEEE 100GBASE-SR10 link specification; the newly developed F-tone 100G CFP transceiver provides increased port density and total system cost savings. The F-tone CFP module has a single MPO port which connects to an industry standard 2x12 multi-mode fiber cable. One 2x12 multi-mode optical fiber cable terminated with MPO optical connectors connects two CFP modules.
CFP Dual 40GBASE-SR4 OTU3 Parallel Optical Module
CFP Dual 40GBASE-SR4 / OTU3 Parallel Optical Module:pictureDesigned to support the IEEE 40GBASE-SR4 link specification; the newly developed F-tone Dual 40G CFP transceiver offers 2 independent 40G Ethernet links in one CFP slot. The F-tone CFP transceiver has two MPO ports which connect to industry standard 12-fiber multi-mode fiber cable. Both MPO ports will inter-operate with equipment using 40GBASE-SR4 QSFP transceivers.
CFP2-100G-LR4
10km OTU4/100G Ethernet CFP2 Optical Transceiver Module (CFP2-100G-LR4),F-tone’s CFP2-100G-LR4 100G CFP2 transceiver modules are designed for use in 100 Gigabit Ethernet and 4x28G OTN client interfaces over single mode fiber. They are compliant with the CFP MSA, IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F requirements specified in ITU-T Recommendations G.959.1/G.709 and Supplement 39 (G.sup39).
Coherent CFP2-ACO 100G/200G Transceiver
Coherent CFP2-ACO 100G/200G Transceiver：The 100Gb/s coherent CFP2 pluggable transceiver, enabled by F-tone Networks’s industry leading InP technology, represents the next generation of high performance optical modules designed for a variety of DWDM lineside applications. The analog coherent CFP2 module offers significant advantages over existing solutions in terms of reduced power dissipation and increased density with the added benefit of pluggability for reduced first installed cost.
100G CFP2 LR4
CFP2 LR4,100G CFP2 LR4:The CFP2-1310-LR4 is a fully integrated 100Gbit/s optical transceiver module that consists of a 1310 nm wavelength cooled EA-DFB LD, Driver IC, PIN photo-diode, pre-amplifier, dual clock and data recovery (CDR) ICs with 25 Gbit/s electrical interface which complies with CFP2 Multiple Source Agreement (MSA) specifications.